Quadranet 服务器benchmark

看到hostloc, quadranet的官方发布了一个sale,最近正好缺多IP的服务器,于是就订了一台跑一些服务。下面先做一些基本的benchmark,然后就要安装ESXi了

使用的程序:

wget -qO- bench.sh | bash

下面是结果:

----------------------------------------------------------------------
CPU model : Intel(R) Xeon(R) CPU E3-1240 v6 @ 3.70GHz
Number of cores : 8
CPU frequency : 799.890 MHz
Total size of Disk : 278.0 GB (1.7 GB Used)
Total amount of Mem : 15834 MB (232 MB Used)
Total amount of Swap : 2047 MB (0 MB Used)
System uptime : 0 days, 6 hour 45 min
Load average : 0.04, 0.04, 0.05
OS : CentOS 7.7.1908
Arch : x86_64 (64 Bit)
Kernel : 3.10.0-1062.12.1.el7.x86_64
----------------------------------------------------------------------
I/O speed(1st run) : 316 MB/s
I/O speed(2nd run) : 317 MB/s
I/O speed(3rd run) : 318 MB/s
Average I/O speed : 317.0 MB/s

—————

用的是老款的intel s3500, 速度勉强可以吧,基本保持在321MB/s左右

检查一下硬盘信息:

[[email protected] ~]# smartctl -a /dev/sda
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-3.10.0-1062.12.1.el7.x86_64] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Intel 730 and DC S35x0/3610/3700 Series SSDs
Device Model: INTEL SSDSC2BB300G4
Serial Number: BTWL40210787300PGN
LU WWN Device Id: 5 5cd2e4 04b56befb
Firmware Version: D2010370
User Capacity: 300,069,052,416 bytes [300 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 T13/2015-D revision 3
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Feb 24 19:41:04 2020 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 2) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0032 100 100 000 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 34840
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 37
170 Available_Reservd_Space 0x0033 100 100 010 Pre-fail Always - 0
171 Program_Fail_Count 0x0032 100 100 000 Old_age Always - 0
172 Erase_Fail_Count 0x0032 100 100 000 Old_age Always - 0
174 Unsafe_Shutdown_Count 0x0032 100 100 000 Old_age Always - 35
175 Power_Loss_Cap_Test 0x0033 100 100 010 Pre-fail Always - 637 (204 414)
183 SATA_Downshift_Count 0x0032 100 100 000 Old_age Always - 2
184 End-to-End_Error 0x0033 100 100 090 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
190 Temperature_Case 0x0022 081 081 000 Old_age Always - 19 (Min/Max 17/20)
192 Unsafe_Shutdown_Count 0x0032 100 100 000 Old_age Always - 35
194 Temperature_Internal 0x0022 100 100 000 Old_age Always - 28
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
199 CRC_Error_Count 0x003e 100 100 000 Old_age Always - 4
225 Host_Writes_32MiB 0x0032 100 100 000 Old_age Always - 61519
226 Workld_Media_Wear_Indic 0x0032 100 100 000 Old_age Always - 911
227 Workld_Host_Reads_Perc 0x0032 100 100 000 Old_age Always - 84
228 Workload_Minutes 0x0032 100 100 000 Old_age Always - 2090316
232 Available_Reservd_Space 0x0033 100 100 010 Pre-fail Always - 0
233 Media_Wearout_Indicator 0x0032 100 100 000 Old_age Always - 0
234 Thermal_Throttle 0x0032 100 100 000 Old_age Always - 0/0
241 Host_Writes_32MiB 0x0032 100 100 000 Old_age Always - 61519
242 Host_Reads_32MiB 0x0032 100 100 000 Old_age Always - 341415

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

再看看sdb:

[[email protected] ~]# smartctl -a /dev/sdb
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-3.10.0-1062.12.1.el7.x86_64] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Intel 730 and DC S35x0/3610/3700 Series SSDs
Device Model: INTEL SSDSC2BB300G4
Serial Number: BTWL347206YW300PGN
LU WWN Device Id: 5 5cd2e4 04b53fc0e
Firmware Version: D2010370
User Capacity: 300,069,052,416 bytes [300 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 T13/2015-D revision 3
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Feb 24 19:43:51 2020 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 2) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0032 100 100 000 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 39582
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 59
170 Available_Reservd_Space 0x0033 100 100 010 Pre-fail Always - 0
171 Program_Fail_Count 0x0032 100 100 000 Old_age Always - 0
172 Erase_Fail_Count 0x0032 100 100 000 Old_age Always - 0
174 Unsafe_Shutdown_Count 0x0032 100 100 000 Old_age Always - 57
175 Power_Loss_Cap_Test 0x0033 100 100 010 Pre-fail Always - 629 (226 417)
183 SATA_Downshift_Count 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 090 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
190 Temperature_Case 0x0022 083 083 000 Old_age Always - 17 (Min/Max 16/17)
192 Unsafe_Shutdown_Count 0x0032 100 100 000 Old_age Always - 57
194 Temperature_Internal 0x0022 100 100 000 Old_age Always - 26
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
199 CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0
225 Host_Writes_32MiB 0x0032 100 100 000 Old_age Always - 4055029
226 Workld_Media_Wear_Indic 0x0032 100 100 000 Old_age Always - 16179
227 Workld_Host_Reads_Perc 0x0032 100 100 000 Old_age Always - 21
228 Workload_Minutes 0x0032 100 100 000 Old_age Always - 2374838
232 Available_Reservd_Space 0x0033 100 100 010 Pre-fail Always - 0
233 Media_Wearout_Indicator 0x0032 085 085 000 Old_age Always - 0
234 Thermal_Throttle 0x0032 100 100 000 Old_age Always - 0/0
241 Host_Writes_32MiB 0x0032 100 100 000 Old_age Always - 4055029
242 Host_Reads_32MiB 0x0032 100 100 000 Old_age Always - 1091089

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

/dev/sdb的media_wearout_indicator 是85,而非100,表明这个 ssd 硬盘已经开始downgraded

给quadranet 发了ticket 要求更换,等等看吧